Automated Marketing

Were you trying to locate ideas concerning How to Install a Bathtub Yourself?

Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to leave the old tub and embeded in the new one. See to it you have actually qualified yourself for the job and fit attempting it. Instead of employing a service provider to take over a halfway-completed project, it is better to take into consideration using one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your restroom if you have currently purchased a new tub and also do not need to change the setup of your previous water pipes.
Your devices as well as material list must make up the following:

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.

Setting up the Tub

Utilizing both wood boards under its feet, put the tub in the needed setting. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the tub until the spirit level reads level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; then do the same for the various other tap.
Activate the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the bath tub and additionally check the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bath tub must wait till the bath tub has actually been used a minimum of when as this will certainly resolve it right into its final position.

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in area between the tap and the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Tiling Around the Tub

In the location where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to pass through the wall surface in between the bathroom and the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water before securing, to permit the activity experienced when the tub is in use. The sealer can break relatively very early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant sticky as well as cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I discovered that blog entry on Tools You Need to Install a New Bathtub when doing a lookup on the search engines. For those who enjoyed reading our article if you please don't forget to share it. We truly appreciate reading our article about How to Install a Bathtub Yourself.

Opt for our expert plumbers.